• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass window Doctor Repair

Professional window repairmen are able to move large panes of tempered glass from a high point above the ground. They adhere to strict safety guidelines and are often working in extreme weather conditions.

Wearing protective clothing, remove the metal glazing points and all glazing putty using an utility knife. A heat gun may help soften the old glue and make it easier to remove.

Replacement

It is tempting to repair the window glass instead of replacing it when the glass breaks. However, replacing windows is typically more cost-effective and may aid in preventing other issues with your home's energy efficiency. Examine the type of broken glass to determine whether it's a temporary fix, or if a more permanent solution is required.

The first step in fixing damaged windows is to take off the sash, or frame and lay it flat on a work table. Wearing eye protection, gently wiggle the window's pane and then remove any remaining fragments. Then, use a knife to remove the glazing compound and points that keep the glass in the position. Be sure to keep the track of the components and their locations to make sure they can be replaced later.

After the frame and sash have been removed and the frame is removed, you can begin preparation to install the new glass. Make sure that the opening of the frame is of the correct size for the replacement window. To allow for the expansion of the frame and glass and contraction, measure both directions across the opening and subtract 1/8 inch. After that, you can purchase double-strength glasses cut to these exact measurements. It is a good idea to purchase enough glazier's clips, or points to install every 6 inches around each window pane.

If the manufacturer is accountable, you can call them and file an claim. After the new glass has been erected it is essential to cover it with a thin layer of glaziers compound. After the compound has dried, you can paint it to match the rest of the frame.

If you have a crack that is more than an inch, cutting a small arc with a razor blade that is just above the crack can help to prevent it from spreading any further. This method isn't infallible, but it will slow the growth of the crack to a manageable level until you are able to take more permanent measures.

Repair

Professional window contractors are trained to deal with a variety of glass and have the tools needed to complete the job correctly. They also understand the best practices for disposing of waste, and are less likely to leave crumbs behind, which could potentially cause harm to pets or family members. They are also experienced in working with different types of windows and could be able spot problems that an inexperienced home owner would not notice.

Before you begin the process of repairing cracked window glass, be sure to wear safety glasses and gloves. A small crack could cause glass shards to fly and pose a risk to anyone in or around the home. It is important to determine what caused the crack, since this can prevent future issues.

Create a two-part mixture of epoxy. They are typically a 50/50 mix of resin and hardener, Window Doctor and must be mixed quickly. After the mix has been prepared, apply it directly to the crack and let it dry. It should take only about a few minutes, but it is important to be quick because the mixture is thick and drys very quickly.

Once the epoxy is dried, you can remove any excess with a knife. You'll need to scrub the cracked glass. If you don't do this properly, the residue can cause further damage to the glass. Use a putty blade to smooth the compound around the edge of the window and match it with the wood frame.

Consider using a plastic cover for a more robust option. You can cover the glass with masking tape or a sturdy trashbag. This will stop the crack from expanding, and will also keep out water, wind insects, water, and other debris.

You can create a temporary fix if you are unable to reach the window in a timely manner. Simply run a bead of the material around the outside of the broken window. It won't completely fill the gap between the frame and glass, but it will keep the broken piece in place while you repair it.

Repainting

If your windows with glass are old, you might need to paint them. This is an affordable alternative to replacing your windows and will give your house a new appearance. Make sure that the surface is clean prior to painting. Wash the window with water and soap or ruby alcohol to get rid of oil smudges as well as other residues which can hinder the paint from adhering. You should also wear rubber gloves when working on glass to avoid transferring your own oils onto the window's surface. Apply several thin coats rather than just one large coat. This will allow the paint to last longer, and keep your windows looking smooth and even.

If you're planning to repaint your glass windows, be sure you have the proper tools in your arsenal. You'll require either a brush or sponge painter's tap, a ruler and toothpicks. It is also recommended to have the brushes and paint you'll use to complete the project. Make sure you adhere to the manufacturer's guidelines and have a good amount of patience since it may take awhile for the paint to dry.

Also, ensure that the area you're working in is well ventilated if you're using solvent-based paint. This will help to reduce the risk of inhaling harmful chemicals, and the paint will dry faster. Use a mask that is protective when using spray paints.

You'll need to wash the glass window thoroughly with soap and warm water prior to you paint it. Clean the glass thoroughly with soap and warm water, then use rubbing alcohol to clean off any oil or grease that could affect the adhesion of the paint. Make sure that the windows are completely dry prior to coating them.

If your glass windows are energy efficient dual pane windows, you might be able to make a claim with the dealer or window company who sold them to cover any repair or replacement costs. This is particularly true if the windows are still under warranty and you've experienced several issues with condensation or broken glass.

Sealing

If you have double-pane windows that have a damaged seal or more recent insulated glass units (IGUs) that have experienced defogging and fogging, there are a variety of options to address the issue. The most costly option is to replace the frame and insulated unit however it could be required if fog or condensation cause energy loss. Other options include replacing the existing IGU with a single-pane or fixing it by drilling a small hole in the bottom of the unit and filling the solution with anti-fog.

You can also seal the gap between the window doctor near me frame and the threshold or sill by using a felt strip vinyl v-strips, or a door sweep. Felt can be stapled, glued or nailed into place but does not offer much protection against moisture. Vinyl v-strip is easy to install and long-lasting however, it can be costly. It is generally used in areas that are subject to high abrasion. Door sweeps are affordable and can be put into place, but they create little to no barrier between the threshold or sill and dust, air, and other debris.

To fix a cracked window seal first, use a putty blade to take off the old caulk. Wearing eye protection and gloves remove the glazing point -- small fasteners with sharp pointed tips that secure the glass to the frame's recess. After you have removed the glazing points, scrub the grooves and sand the wood smooth. Clean any sanding residue, then seal the bare wood with a linseed oil-based paint or clear wood sealer.

A caulking knife or putty can be used to apply traditional glazing putty, however using a knife will give a more precise application, and a stronger seal. Choose a putty that is specifically designed for glass as it is more durable and will adhere better.

Apply a thin layer of putty on the inside of the frame where it joins the glass. Slide the window into frame so that the scribed line on glass aligns with edge of frame. Apply pressure to the glass in order to press the putty into a tight seal. Smooth the compound with a gloved hand and remove any drips or caulk that were applied incorrectly before it has dried.